Body Lift Kits

Body Lift Kits Index

Last Updated: 22/06/07

Marks 4WD Adaptors is an Australian company, specialising in the design and manufacture of quality accessories that enhance the off road performance of four wheel drive vehicles.

Body lift kits are available for a large range of vehicles. The kits consist of spacers and bolts and can be supplied singularly as the number required does vary from vehicle to vehicle.

The spacers are manufactured from either mild steel bar which is zinc plated for corrosion resistance or alternately impact resistant nylon. The bolts supplied are corrosion resistant stainless steel or grade 8.8 high tensile steel.

All of the following kits are supplied with 70mm x 3mm washers which are fitted between the body and the body lift spacers. We highly recommend welding these washers to the body for maximum strength. This photo shows a cracked body mounting point on a Toyota with a 2" lift. The body spacers in this vehicle were not previously fitted with strengthening washers. To carry out the repair we welded the cracks, ground the welds flat and then welded the strengthening washers in place.

Toyota RJ70 Land Cruiser fitted with a 2" body lift (35" tyres). photo

Toyota 4RUNNER fitted with a 2" body lift compared to a std Hilux. photo 1, photo 2

Nissan SWB GQ fitted with a 3" body lift (35" tyres). photo

Basic Fitting Requirements

25mm body lifts are the easiest to fit requiring very few modifications. The front and rear bars in most cases don't require lifting.

50mm body lifts will require some modifications for a successful installation. Gear levers will need to be bent and in some cases lengthened. Gear lever boots may also need modification to reduce the possibility of gear drop out from extra boot load. After fitting a body lift kit the front and rear bar mounting points will need to be raised for best appearance. Clutch hydraulic hose, mounting points can also require shifting.

Our engineer gives us the green light on all body lift kits up to 2" high, any more than that will not be road legal without undergoing stringent stress testing. However special purpose off road vehicles may require higher lift to allow for larger tyres and modified suspension.

Body lift spacers and bolts can be bought individually to enable you to build a kit for your special application.

This is a photo of our latest design body lift spacers, they have been made wider at the top to reduce body movement and better match the 75mm diameter 3mm thick washers which are supplied in all of our kits.

Land Cruiser Body Lift Kits

60 series body lift kits

60 series 25mm body lift kit.

60 series 50mm body lift kit.

PART NO. MFK1442/12/25 RRP AU$240 inc GST
The Kit consists of: 12 spacers 25Lx60x11, 12 bolts, 12 nylock nuts, and washers.

PART NO. MFK1442/12/50 RRP AU$300 inc GST
The Kit consists of: 12 spacers 50Lx60x11, 12 bolts, 12 nylock nuts, and washers.

60 series 75mm body lift kit.

PART NO. MFK1442/12/75 RRP AU$360 inc GST
The Kit consists of: 12 spacers 75Lx60x11, 12 bolts, 12 nylock nuts, and washers.

70 series cab chassis body lift kits

70 series 25mm body lift kit.

70 series 50mm body lift kit.

PART NO. MFK1443/6/25 RRP AU$120 inc GST
The Kit consists of: 6 spacers 25Lx60x11, 6 bolts, 6 nylock nuts, and washers.

PART NO. MFK1443/6/50 RRP AU$150 inc GST
The Kit consists of: 6 spacers 50Lx60x11, 6 bolts, 6 nylock nuts, and washers.

70 series 75mm body lift kit.

NOTE: These cab chassis body lift kits will only lift the cab. If your vehicle is fitted with a ute body and you wish to raise it with the cab, extra spacers will need to be purchased. Some tray bodies can also be lifted this way or alternately 50X50 RHS can be used.

PART NO. MFK1443/6/75 RRP AU$180 inc GST
The Kit consists of: 6 spacers 75Lx60x11, 6 bolts, 6 nylock nuts, and washers.

70 series Bundera body lift kit

Bundera 25mm body lift kit.

Bundera 50mm body lift kit.

PART NO. MFK1440B/25 RRP AU$160 inc GST
The Kit consists of: 8 spacers 25Lx60x11, 8 bolts, and 8 nylock nuts.

PART NO. MFK1440B/50 RRP AU$200 inc GST
The Kit consists of: 8 spacers 50Lx60x11, 8 bolts, and 8 nylock nuts.

Bundera 75mm body lift kit.

PART NO. MFK1440B/75 RRP AU$240 inc GST
The Kit consists of: 8 spacers 75Lx60x11, 8 bolts, and 8 nylock nuts.

73 series Mid Wheel Base body lift kit

73 series mid wheel base 25mm body lift kit.			73 series mid wheel base 50mm body lift kit.
	PART NO. MFK14403/12/25 RRP AU$240 inc GST The Kit consists of: 12 spacers 50Lx60x11, 12 bolts, 12 washers and nylock nuts.			PART NO. MFK14403/12/50 RRP AU$300 inc GST The Kit consists of: 12 spacers 50Lx60x11, 12 bolts, 12 washers and nylock nuts.

80 series body lift kit

80 series 25mm body lift kit.

80 series 50mm body lift kit.

PART NO. MFK1446/12/25 RRP AU$240 inc GST
The Kit consists of: 12 spacers 25Lx60x11, 12 bolts, 12 nylock nuts, and washers.

PART NO. MFK1446/12/50 RRP AU$300 inc GST
The Kit consists of: 12 spacers 50Lx60x11, 12 bolts, 12 nylock nuts, and washers.

80 series 75mm body lift kit.

PART NO. MFK1446/12/75 RRP AU$360 inc GST
The Kit consists of: 12 spacers 75Lx60x11, 12 bolts, 12 nylock nuts, and washers.

Hilux/4Runner Body Lift Kits

Hilux Single Cab lift kits

Hilux Single Cab Body Only 25mm lift kit.

Hilux Single Cab Body Only 50mm lift kit.

PART NO. MFK1440H/25 RRP AU$120 inc GST
The Kit consists of: 6 spacers 25Lx60x11, 6 stainless bolts, and 6 nylock nuts and washers.

PART NO. MFK1440H/50 RRP AU$150 inc GST
The Kit consists of: 6 spacers 50Lx60x11, 6 stainless bolts, and 6 nylock nuts and washers.

Hilux Single Cab Body Only 75mm lift kit.

PART NO. MFK1440H/75 RRP AU$180 inc GST
The Kit consists of: 6 spacers 75Lx60x11, 6 stainless bolts, and 6 nylock nuts and washers.

Hilux Single Cab and Tub lift kits

Hilux Single Cab and Tub 25mm lift kit.

Hilux Single Cab and Tub 50mm lift kit.

PART NO. MFK1440HT/25 RRP AU$280 inc GST
The Kit consists of: 14 spacers 25Lx60x11, 14 stainless bolts, and 14 nylock nuts and washers.

PART NO. MFK1440HT/50 RRP AU$350 inc GST
The Kit consists of: 14 spacers 50Lx60x11, 14 stainless bolts, and 14 nylock nuts and washers.

Hilux Single Cab and Tub 75mm lift kit.

PART NO. MFK1440HT/75 RRP AU$420 inc GST
The Kit consists of: 14 spacers 75Lx60x11, 14 stainless bolts, and 14 nylock nuts and washers.

4/Runner body lift kits

4/Runner 25mm body lift kit.

4/Runner 50mm body lift kit.

PART NO. MFK1440/4R/25 RRP AU$200 inc GST
The Kit consists of: 10 spacers 25Lx60x11, 10 stainless bolts, and 10 nylock nuts and washers.

PART NO. MFK1440/4R/50 RRP AU$250 inc GST
The Kit consists of: 10 spacers 50Lx60x11, 10 stainless bolts, and 10 nylock nuts and washers.

4/Runner 75mm body lift kit.

PART NO. MFK1440/4R/75 RRP AU$300 inc GST
The Kit consists of: 10 spacers 75Lx60x11, 10 stainless bolts, and 10 nylock nuts and washers.

Toyota Surf body lift kit

4/Runner 25mm body lift kit.

PART NO. MFK1440/SURF/50 RRP AU$250 inc GST
The kit consists of: 10 spacers 25Lx60x11, 10 stainless bolts, and 10 nylock nuts and washers.

Nissan Navara Body Lift Kits

Navara D22 body lift kits

Nissan Navara D22 1997 on 50mm body lift kit.

PART NO. MFK1452/50 RRP AU$450 inc GST
The kit consists of: 14 body mounting spacers, 4 cross member support spacers, bolts, and nuts, washers and instructions.

Before and after photos.

Nissan GQ Body Lift Kits

GQ SWB body lift kits

Nissan GQ SWB 25mm body lift kit.

Nissan GQ SWB 50mm body lift kit.

PART NO. MFK1450/8/25 RRP AU$160 inc GST
The Kit consists of: 8 spacers 25Lx60x11, bolts, and nuts, washers and instructions.

PART NO. MFK1450/8/50 RRP AU$200 inc GST
The Kit consists of: 8 spacers 50Lx60x11, bolts, and nuts, washers and instructions.

Nissan GQ SWB 75mm body lift kit.

PART NO. MFK1450/8/75 RRP AU$240 inc GST
The Kit consists of: 8 spacers 75Lx60x11, bolts, and nuts, washers and instructions.

GQ LWB body lift kits

Nissan GQ LWB 25mm body lift kit.

Nissan GQ LWB 50mm body lift kit.

PART NO. MFK1450/10/25 RRP AU$200 inc GST
The Kit consists of: 10 spacers 25Lx60x11, bolts, and nuts, washers and instructions.

PART NO. MFK1450/10/50 RRP AU$250 inc GST
The Kit consists of: 10 spacers 50Lx60x11, bolts, and nuts, washers and instructions.

Nissan GQ LWB 75mm body lift kit.

PART NO. MFK1450/10/75 RRP AU$300 inc GST
The Kit consists of: 10 spacers 75Lx60x11, bolts, and nuts, washers and instructions.

Body Lift Parts

25mm Body Lift Spacers

25mm Nylon Spacer.

PART NO. MFK1440/25 RRP AU$15 inc GST
The kit consists of: Spacer 25Lx60x11

50mm Body Lift Spacers

50mm Steel Spacer.			50mm Nylon Spacer.
	PART NO. MFK1440 RRP AU$20 inc GST The Kit consists of: Spacer 50Lx50x11 zinc plated.			PART NO. MFK1440/50 RRP AU$20 inc GST The Kit consists of: Spacer 50Lx60x11

75mm Body Lift Spacers

75mm Nylon Spacer.

PART NO. MFK1440/75 RRP AU$25 inc GST
The kit consists of: Spacer 75Lx60x11

Bolts

M10x140mm Stainless bolt.

M10x110mm Stainless bolt.

PART NO. MFK1444 RRP AU$12 inc GST
The Kit consists of: One bolt and one nylock nut.

PART NO. MFK1155 RRP AU$10 inc GST
The Kit consists of: One bolt and one nylock nut.

M10x150mm steel bolt.

M10x200mm steel bolt.

PART NO. MFK1512 RRP AU$5 inc GST
The Kit consists of: One bolt and one nylock nut.

PART NO. MFK1513 RRP AU$5 inc GST
The Kit consists of: One bolt and one nylock nut.

Nissan GQ 4.2ltr Hi/Low Lever Locking Plate

Nissan GQ Hi/Low Lever Locking Plate kit.

Vehicles fitted with 50mm or higher body lifts require the hi/low gear lever to be extended, the gear lever boot also requires modification to allow for the extra travel of the lever in the boot. the extra travel increases the pressure put on the lever by the boot, this can, under some conditions allow the lever to select 4WD when not required. This locking plate allows the hi/low lever to be locked positively into high range 2WD or 4WD.

PART NO. MFK1440LP RRP AU$45 inc GST
The Kit consists of: Hi/Low Lever Locking Plate.

Steering Shaft Extension

Steering Extension Shaft.

Vehicles being fitted with body lifts higher than 50mm require the use of a steering shaft extension. When the body is lifted the steering shaft needs to be made longer, the splined extension is a simple bolt in solution to this problem.

PART NO. MFK1440HSE RRP AU$130 inc GST
The Kit consists of: Splined extension shaft.

60 series 25mm body lift kit.		60 series 50mm body lift kit.
	PART NO. MFK1442/12/25 RRP AU$240 inc GST The Kit consists of: 12 spacers 25Lx60x11, 12 bolts, 12 nylock nuts, and washers.		PART NO. MFK1442/12/50 RRP AU$300 inc GST The Kit consists of: 12 spacers 50Lx60x11, 12 bolts, 12 nylock nuts, and washers.
60 series 75mm body lift kit.
	PART NO. MFK1442/12/75 RRP AU$360 inc GST The Kit consists of: 12 spacers 75Lx60x11, 12 bolts, 12 nylock nuts, and washers.

70 series 25mm body lift kit.		70 series 50mm body lift kit.
	PART NO. MFK1443/6/25 RRP AU$120 inc GST The Kit consists of: 6 spacers 25Lx60x11, 6 bolts, 6 nylock nuts, and washers.		PART NO. MFK1443/6/50 RRP AU$150 inc GST The Kit consists of: 6 spacers 50Lx60x11, 6 bolts, 6 nylock nuts, and washers.
70 series 75mm body lift kit.			NOTE: These cab chassis body lift kits will only lift the cab. If your vehicle is fitted with a ute body and you wish to raise it with the cab, extra spacers will need to be purchased. Some tray bodies can also be lifted this way or alternately 50X50 RHS can be used.
	PART NO. MFK1443/6/75 RRP AU$180 inc GST The Kit consists of: 6 spacers 75Lx60x11, 6 bolts, 6 nylock nuts, and washers.

Bundera 25mm body lift kit.		Bundera 50mm body lift kit.
	PART NO. MFK1440B/25 RRP AU$160 inc GST The Kit consists of: 8 spacers 25Lx60x11, 8 bolts, and 8 nylock nuts.		PART NO. MFK1440B/50 RRP AU$200 inc GST The Kit consists of: 8 spacers 50Lx60x11, 8 bolts, and 8 nylock nuts.
Bundera 75mm body lift kit.
	PART NO. MFK1440B/75 RRP AU$240 inc GST The Kit consists of: 8 spacers 75Lx60x11, 8 bolts, and 8 nylock nuts.

80 series 25mm body lift kit.		80 series 50mm body lift kit.
	PART NO. MFK1446/12/25 RRP AU$240 inc GST The Kit consists of: 12 spacers 25Lx60x11, 12 bolts, 12 nylock nuts, and washers.		PART NO. MFK1446/12/50 RRP AU$300 inc GST The Kit consists of: 12 spacers 50Lx60x11, 12 bolts, 12 nylock nuts, and washers.
80 series 75mm body lift kit.
	PART NO. MFK1446/12/75 RRP AU$360 inc GST The Kit consists of: 12 spacers 75Lx60x11, 12 bolts, 12 nylock nuts, and washers.

Hilux Single Cab Body Only 25mm lift kit.		Hilux Single Cab Body Only 50mm lift kit.
	PART NO. MFK1440H/25 RRP AU$120 inc GST The Kit consists of: 6 spacers 25Lx60x11, 6 stainless bolts, and 6 nylock nuts and washers.		PART NO. MFK1440H/50 RRP AU$150 inc GST The Kit consists of: 6 spacers 50Lx60x11, 6 stainless bolts, and 6 nylock nuts and washers.
Hilux Single Cab Body Only 75mm lift kit.
	PART NO. MFK1440H/75 RRP AU$180 inc GST The Kit consists of: 6 spacers 75Lx60x11, 6 stainless bolts, and 6 nylock nuts and washers.

Hilux Single Cab and Tub 25mm lift kit.		Hilux Single Cab and Tub 50mm lift kit.
	PART NO. MFK1440HT/25 RRP AU$280 inc GST The Kit consists of: 14 spacers 25Lx60x11, 14 stainless bolts, and 14 nylock nuts and washers.		PART NO. MFK1440HT/50 RRP AU$350 inc GST The Kit consists of: 14 spacers 50Lx60x11, 14 stainless bolts, and 14 nylock nuts and washers.
Hilux Single Cab and Tub 75mm lift kit.
	PART NO. MFK1440HT/75 RRP AU$420 inc GST The Kit consists of: 14 spacers 75Lx60x11, 14 stainless bolts, and 14 nylock nuts and washers.

4/Runner 25mm body lift kit.		4/Runner 50mm body lift kit.
	PART NO. MFK1440/4R/25 RRP AU$200 inc GST The Kit consists of: 10 spacers 25Lx60x11, 10 stainless bolts, and 10 nylock nuts and washers.		PART NO. MFK1440/4R/50 RRP AU$250 inc GST The Kit consists of: 10 spacers 50Lx60x11, 10 stainless bolts, and 10 nylock nuts and washers.
4/Runner 75mm body lift kit.
	PART NO. MFK1440/4R/75 RRP AU$300 inc GST The Kit consists of: 10 spacers 75Lx60x11, 10 stainless bolts, and 10 nylock nuts and washers.

4/Runner 25mm body lift kit.
	PART NO. MFK1440/SURF/50 RRP AU$250 inc GST The kit consists of: 10 spacers 25Lx60x11, 10 stainless bolts, and 10 nylock nuts and washers.

Nissan Navara D22 1997 on 50mm body lift kit.
	PART NO. MFK1452/50 RRP AU$450 inc GST The kit consists of: 14 body mounting spacers, 4 cross member support spacers, bolts, and nuts, washers and instructions.

Nissan GQ SWB 25mm body lift kit.		Nissan GQ SWB 50mm body lift kit.
	PART NO. MFK1450/8/25 RRP AU$160 inc GST The Kit consists of: 8 spacers 25Lx60x11, bolts, and nuts, washers and instructions.		PART NO. MFK1450/8/50 RRP AU$200 inc GST The Kit consists of: 8 spacers 50Lx60x11, bolts, and nuts, washers and instructions.
Nissan GQ SWB 75mm body lift kit.
	PART NO. MFK1450/8/75 RRP AU$240 inc GST The Kit consists of: 8 spacers 75Lx60x11, bolts, and nuts, washers and instructions.

Nissan GQ LWB 25mm body lift kit.		Nissan GQ LWB 50mm body lift kit.
	PART NO. MFK1450/10/25 RRP AU$200 inc GST The Kit consists of: 10 spacers 25Lx60x11, bolts, and nuts, washers and instructions.		PART NO. MFK1450/10/50 RRP AU$250 inc GST The Kit consists of: 10 spacers 50Lx60x11, bolts, and nuts, washers and instructions.
Nissan GQ LWB 75mm body lift kit.
	PART NO. MFK1450/10/75 RRP AU$300 inc GST The Kit consists of: 10 spacers 75Lx60x11, bolts, and nuts, washers and instructions.

25mm Nylon Spacer.
	PART NO. MFK1440/25 RRP AU$15 inc GST The kit consists of: Spacer 25Lx60x11

75mm Nylon Spacer.
	PART NO. MFK1440/75 RRP AU$25 inc GST The kit consists of: Spacer 75Lx60x11

M10x140mm Stainless bolt.		M10x110mm Stainless bolt.
	PART NO. MFK1444 RRP AU$12 inc GST The Kit consists of: One bolt and one nylock nut.		PART NO. MFK1155 RRP AU$10 inc GST The Kit consists of: One bolt and one nylock nut.
M10x150mm steel bolt.		M10x200mm steel bolt.
	PART NO. MFK1512 RRP AU$5 inc GST The Kit consists of: One bolt and one nylock nut.		PART NO. MFK1513 RRP AU$5 inc GST The Kit consists of: One bolt and one nylock nut.

Nissan GQ Hi/Low Lever Locking Plate kit.			Vehicles fitted with 50mm or higher body lifts require the hi/low gear lever to be extended, the gear lever boot also requires modification to allow for the extra travel of the lever in the boot. the extra travel increases the pressure put on the lever by the boot, this can, under some conditions allow the lever to select 4WD when not required. This locking plate allows the hi/low lever to be locked positively into high range 2WD or 4WD.
	PART NO. MFK1440LP RRP AU$45 inc GST The Kit consists of: Hi/Low Lever Locking Plate.

Steering Extension Shaft.			Vehicles being fitted with body lifts higher than 50mm require the use of a steering shaft extension. When the body is lifted the steering shaft needs to be made longer, the splined extension is a simple bolt in solution to this problem.
	PART NO. MFK1440HSE RRP AU$130 inc GST The Kit consists of: Splined extension shaft.