-
Diff Overhaul Kit - LandCruiser 78, 79, 100, 105 Series (Rear) (Solid Spacer)
AUD $250.00AUD $250.00 (ex. tax)× -
Holden V8 to LandCruiser 55 / 75 Series - Engine Chassis Brackets
AUD $450.00AUD $450.00 (ex. tax)× -
Engine Chassis Brackets - Chev V8 to Toyota Landcruiser 55 / 75 Series
AUD $190.91AUD $190.91 (ex. tax)× -
Bendix Ultimate 4WD Brake Pads - Toyota LandCruiser 70, 100 Series (Front Pads)
AUD $213.64AUD $213.64 (ex. tax)× -
Clutch Kit (Organic Plate) - Chev V8 Petrol 12" - 10 Tooth Spline
AUD $972.00AUD $1,944.00 (ex. tax)× -
Bell Housing Adaptor Kit - Chev V8 Petrol (late) 168 Tooth Flywheel - LandCruiser (3F 4-speed auto)
AUD $1,813.64AUD $1,813.64 (ex. tax)× -
High Clearance Towbar with Soft Shackle Recovery Points- Toyota LandCruiser 79 Series
AUD $1,704.55AUD $1,704.55 (ex. tax)× -
Gearbox Rebuild Kit - Hilux LAN25, LN, RN, RZN, YN Series / LandCruiser R70, R73
AUD $447.27AUD $447.27 (ex. tax)× -
Clutch Kit - Holden VR Series 2 VS / VT (T5 manual) 10.5" - 10T Spline
AUD $404.55AUD $404.55 (ex. tax)× -
Bendix 4WD Brake Pads - Toyota LandCruiser 4.5D, (VDJ200) (Front Pads)
AUD $86.36AUD $86.36 (ex. tax)× -
Integrated Lithium Auxiliary Battery Kit by Cangoee - Toyota LandCruiser 300 Series MY23
AUD $4,009.09AUD $4,009.09 (ex. tax)× -
Ultra Vision Nitro Maxx 24" 205W LED Light Bar (4500K) Hi/Lo Beam
AUD $899.09AUD $899.09 (ex. tax)× -
Bendix 4WD Brake Rotor - Toyota LandCruiser 200 Series (Front Rotor)
AUD $327.27AUD $327.27 (ex. tax)× -
Bell Housing Adaptor Kit - Holden V8 (Trimatic Pattern) to LandCruiser pre 10/1984 (Manual)
AUD $4,540.91AUD $4,540.91 (ex. tax)× -
Hose Runner Bracket Kit - Toyota Hilux LS2 / LS3 V8 (2005-2015) KUN26R
AUD $177.27AUD $177.27 (ex. tax)× -
Gear Select Module Install Kit - GM 4L60, 65, 70, 80, 85 with PRNDL
AUD $86.36AUD $86.36 (ex. tax)× -
Ultra Vision - Single Pole (On/Off) Switch - Hilux GUN, Prado 150, LandCruiser 200-300 Series
AUD $29.09AUD $29.09 (ex. tax)× -
Bell Housing Adaptor Kit - Chev V8 Petrol to Land Rover / Range Rover (4 / 5-speed manual)
AUD $1,500.00AUD $3,000.00 (ex. tax)× -
Navara D40 Ø 320mm - Delios Slotted Front Brake Rotors (1 x Pair)
AUD $290.91AUD $290.91 (ex. tax)× -
Bell Housing Adaptor Kit - Holden V8 (Trimatic Pattern) to Hilux Gearbox (R150F, R151F 5-speed manual)
AUD $1,813.64AUD $1,813.64 (ex. tax)× -
Transfer Case Adaptor - 4L60E to LandCruiser 60, 70 Series 5-Speed (Split Case)
AUD $2,604.55AUD $2,604.55 (ex. tax)× -
Nissan Patrol GQ / GU - Low Range Gear Set - 24% (2.484:1) Reduction
AUD $1,813.64AUD $1,813.64 (ex. tax)×
Mitsubishi Gen 4 – Low Range Gears 66% (3.15:1) Reduction – Auto 3.2D
AUD $2,395.00 (Excl. Tax AUD $2,177.27)
To Suit – Mitsubishi
- Generation 4 transfer case – 19 tooth (spline) input gear
- Pajero 3.2 Diesel Auto
Low Range Gears 66% (3.15:1) Reduction to Suit Mitsubishi Gen 4
Marks 4WD Adaptors manufacture low range reduction gears to suit many models of Mitsubishi Pajero, Montero, Shogun, Triton, Delica, L200 and L300. These gears are manufactured in-house at our facility in Melbourne, Australia. We manufacture two reduction ratios for the Generation 3 transfer cases to suit different vehicle applications and requirements.
The 66% reduction gears give you the biggest reduction we offer and suit vehicles fitted with an automatic transmission. These are mainly suited to rock-crawling vehicles or vehicles that are prone to run away downhill. For example, this reduction gives a manual vehicle about one and a half gears below where the factory gearing sat. High range is not altered when fitting our low-range gears.
To calculate your Vehicle’s ratio, click here.
Will these Gears fit my Vehicle?
You will need to remove and open the transfer case and check the idler gear has external shoulders for the roller bearings and that the face width of the gear must be approximately 25mm and 20mm, respectively. Please see the image below for reference;
Mitsubishi Pajero Gen 4 Low Range Gear Measurements
Features
- 100% Australian Made
- Designed & Manufactured in-house at Marks4wd
Kit Includes
- Input gear
- Idler gear
- Output gear
- Backlash eliminator
- Downloadable Instructions (requires login)
To Suit – Mitsubishi
Generation 4 transfer case – 19 tooth (spline) input gear
- Pajero 3.2 Diesel Auto
Notes
- A Mitsubishi workshop manual is required for fitment
- The input gear spline is 19T
Customers reviews
Only logged in customers who have purchased this product may leave a review.
There are no reviews yet.