-
Catch Can & Diesel Fuel Water Separator kit by Ryco - Isuzu D-Max, MU-X / Mazda BT50
AUD $760.00AUD $760.00 (ex. tax)× -
Bendix 4WD Brake Rotors - Toyota LandCruiser 105 Series (Rear Rotors)
AUD $359.09AUD $359.09 (ex. tax)× -
Transfer Case Rebuild Kit - LandCruiser 80 / HDJ100 Series (Full Time 4WD)
AUD $786.36AUD $786.36 (ex. tax)× -
Land Rover Discovery I (early) - Braided Brake Lines - Complete Set
AUD $322.73AUD $322.73 (ex. tax)× -
Bell Housing Adaptor Kit - Chev V8 Petrol 153 Tooth Flywheel to Patrol GQ / GU Petrol (Auto)
AUD $2,722.73AUD $2,722.73 (ex. tax)× -
Clutch Kit (Organic Plate) - Chev V8 Petrol 12" - 10 Tooth Spline
AUD $972.00AUD $972.00 (ex. tax)× -
Bell Housing Adaptor Kit - Chev V8 Petrol (early) 168 Tooth Flywheel to LandCruiser 80 Series 4.0L 3F (5-speed manual)
AUD $3,054.55AUD $3,054.55 (ex. tax)× -
Catch Can & Diesel Fuel Water Separator kit by Ryco - Ford Ranger / Mazda BT50
AUD $760.00AUD $760.00 (ex. tax)× -
Bendix 4WD ULT Brake Rotors - Ford Ranger PX / Mazda BT50 (Front Rotors)
AUD $368.18AUD $368.18 (ex. tax)× -
Nissan Patrol GQ / GU - Low Range Gear Set - 43% (2.86:1) Reduction
AUD $1,813.64AUD $1,813.64 (ex. tax)× -
LandCruiser 80 Series - Delios Slotted Front Brake Rotors (01/1990 - 08/1992) (1 x Pair)
AUD $277.27AUD $554.55 (ex. tax)× -
Toyota LandCruiser 80 Series - Delios Slotted Rear Brake Rotors (01/1990 - 08/1992) (1 x Pair)
AUD $277.27AUD $277.27 (ex. tax)× -
Chassis Mount Bracket (Heavy Duty) - Hilux LN / RN (LFS) Single bracket
AUD $200.00AUD $200.00 (ex. tax)× -
Bell Housing Adaptor Kit - Chev V8 Diesel to LandCruiser FJ Petrol (Manual)
AUD $2,136.36AUD $2,136.36 (ex. tax)×
Chev V8 (early) 168T to LandCruiser 4.2L 5-speed manual
AUD $4,150.00 (Excl. Tax AUD $3,772.73)
To Suit – Toyota LandCruiser
- 4.2L 1HZ 5-speed manual
Bell Housing Adaptor Kit to Suit Chev V8 (early) 168T to LandCruiser 4.2L 5-speed manual
The flywheel housing is supplied which measures 61mm/2.4″ long. This housing has the GM bolt pattern on the front and the Toyota 1HZ, bolt pattern on the rear.
The new flywheel supplied in the kit accepts the original Toyota 11″ clutch. The flywheel is offset to the rear to place the clutch in its original position. The flywheel has no ring gear and must be used with the original GM flex plate and ring gear. Spacers and bolts are supplied to fix the flexplate to the flex-plate stiffener.
When ordering a Chevy kit you must make sure that the GM starter motor you intend to use is the correct type. Chevy V8 engines were released with two flywheel and flexplate sizes; they were fitted with a 153 tooth ring gear or 168 tooth ring gear, as a result, two starter motor offsets are available.
The kit will only suit the 168-tooth ring gear.
It will also be necessary to identify the year of the engine, after 1986 the engine crankshaft bolt pattern changed. The bolt pattern is smaller as is the spigot, which locates the flywheel on the crankshaft (52.4-mm). The post-1986 Chevy small block engines are also externally balanced. One way to identify a late model Chevy engine is by the one-piece external, rear main oil seal.
Clutch Kits
Kit Includes
- Adaptor housing
- Crank adaptor
- Flex-plate stiffener
- Steel flywheel
- Flywheel cover plate
- Spigot bearing
- Oil pressure sender adaptor
- Water temperature sender adaptor
- Dowels
- Bolts, Washers
- Downloadable Instructions
To Suit – Toyota LandCruiser
- 4.2L 1HZ 5-speed manual
Notes
- This kit will only suit the early Chev V8 (pre-1986)
- You will need to reuse the original 168T GM auto flex plate from your engine.
Customers reviews
Only logged in customers who have purchased this product may leave a review.
There are no reviews yet.