-
Transfer Case Adaptor - 4L60E to Hilux 5-Speed (Gear Driven Case)
AUD $1,813.64AUD $1,813.64 (ex. tax)× -
Catch Can & Diesel Fuel Water Separator kit by Ryco - Isuzu D-Max, MU-X / Mazda BT50
AUD $760.00AUD $760.00 (ex. tax)× -
LandCruiser 70 Series - Delios Slotted Rear Brake Rotors (1 x Pair)
AUD $281.82AUD $281.82 (ex. tax)× -
Catch Can & Diesel Fuel Water Separator kit by Ryco - Mitsubishi Pajero Sport & Triton
AUD $760.00AUD $760.00 (ex. tax)× -
Mitsubishi Gen 2 - Low Range Gears 40% (2.7:1) Reduction (Auto)
AUD $2,177.27AUD $2,177.27 (ex. tax)× -
Wheel Bearing Kit - LandCruiser (1975-2012) & Hilux (Up to '97) Drum Brakes
AUD $63.64AUD $63.64 (ex. tax)× -
Chev V8 / V6 4.3L to LandCruiser FJ40, FJ60, FJ62, FJ80 - Engine Mount Kit
AUD $340.91AUD $681.82 (ex. tax)× -
Engine Chassis Brackets - Chev V8 to Toyota Landcruiser 55 / 75 Series
AUD $190.91AUD $190.91 (ex. tax)× -
Ultra Vision - Single Pole (On/Off) Switch- LandCruiser 70, 100, 105 series, Hilux, Prado 120
AUD $29.09AUD $29.09 (ex. tax)× -
Transfer Case Adaptor - 4L60E to Hilux V6 5-Speed, 26T Input Spline (Chain Driven Case)
AUD $2,786.36AUD $2,786.36 (ex. tax)× -
Hilux 4WD - Delios Slotted Front Brake Rotors (2010 - On) (1 x Pair)
AUD $340.91AUD $340.91 (ex. tax)× -
Brake Upgrade Package- Toyota LandCruiser 70 Series (08/2019 Onwards) & FREE Bendix LED Penlight & Stubby Holder
AUD $2,969.09AUD $2,969.09 (ex. tax)× -
Diff Overhaul Kit - LandCruiser 78, 79, 100, 105 Series (Rear) (Solid Spacer)
AUD $250.00AUD $500.00 (ex. tax)× -
Viscous Fan Adaptor - Toyota Fan to Chev / Holden Petrol Engines
AUD $204.55AUD $204.55 (ex. tax)× -
Holden V8 to LandCruiser 55 / 75 Series - Engine Chassis Brackets
AUD $450.00AUD $450.00 (ex. tax)× -
Nissan Patrol GQ / GU - Low Range Gear Set - 75% (3.56:1) Reduction
AUD $1,995.45AUD $1,995.45 (ex. tax)× -
Diff Overhaul Kit - LandCruiser 76, 78, 79, 100, 105, 200 Series (Rear)
AUD $404.55AUD $404.55 (ex. tax)× -
Bell Housing Adaptor Kit - Holden V8 (Turbo Pattern) to LandCruiser 4.2L 1HZ (5-speed)
AUD $4,059.09AUD $4,059.09 (ex. tax)× -
Land Rover Discovery I (early) - Braided Brake Lines - Complete Set
AUD $322.73AUD $322.73 (ex. tax)× -
Chassis Mount Bracket (Heavy Duty) - Hilux LN / RN (LFS) Single bracket
AUD $200.00AUD $200.00 (ex. tax)× -
Fan Shroud & Hose Kit - LS Series V8 to Patrol GU (RD28 / ZD30)
AUD $1,059.09AUD $1,059.09 (ex. tax)× -
LandCruiser 70, 105 Series - Delios Slotted Front Brake Rotors (1 x Pair)
AUD $281.82AUD $281.82 (ex. tax)× -
Bendix Ultimate 4WD Brake Pads - Toyota LandCruiser 70, 80, 105 Series (Rear Pads)
AUD $213.64AUD $213.64 (ex. tax)×
Mitsubishi Gen 2 – Low Range Gears – 66% (3.15:1) Reduction – Auto
AUD $2,395.00 (Excl. Tax AUD $2,177.27)
Mitsubishi low range gears – ratio 3.15:1 – automatic transmission
To Suit
Generation 2 transfer case – 23 tooth (spline) input gear
- Montero
- Pajero
- Shogun
- Triton
Mitsubishi Gen 2 – Low Range Gears – 66% (3.15:1) Reduction
Marks 4WD Adaptors manufacture low range reduction gears to suit many models of Mitsubishi Pajero, Montero, Shogun and Triton. These gears are manufactured in house at our facility in Melbourne, Australia. We manufacture two reduction ratios for the Generation 2 transfer cases to suit different vehicle applications and requirements.
The 66% reduction gears give you the biggest reduction we offer and suit vehicles fitted with a automatic transmission. These are mainly suited to rock crawling vehicles or vehicles that are prone to run away down hill (fitted with an automatic transmission). As an example this reduction gives a manual vehicle about one and a half gears below where the factory gearing sat. High range is not altered when fitting our low range gears.
To calculate your vehicle’s ratio, click here.
Will these gears fit my vehicle?
You will need to remove and open the transfer case and check the idler gear has external shoulders for the roller bearings and the face width of the gear must be approximately 30mm and 28mm respectively. Please see image below for reference;
Mitsubishi Pajero Gen 2 Low Range Gear Measurements
Features
- 100% Australian Made
- Designed & Manufactured in-house at Marks4wd
Kit Includes
- Input gear
- Idler gear
- Output gear
- Roller bearing
- Seals
To Suit – Mitsubishi
Generation 2 transfer case – 23 tooth (spline) input gear
- Montero
- Pajero
- Shogun
- Triton
Notes
- A Mitsubishi workshop manual is required for fitment
- The input gear spline is 23T – 31.3mm in diameter
Customers reviews
Only logged in customers who have purchased this product may leave a review.
There are no reviews yet.