-
DB1365 - G4O 4WD Brake Pads – Toyota LandCruiser 70, 100 Series (Front Pads)
AUD $190.91AUD $381.82 (ex. tax)× -
LandCruiser 70, 105 Series - Delios Slotted Front Brake Rotors (1 x Pair)
AUD $281.82AUD $281.82 (ex. tax)× -
Handbrake Shoe Kit - LandCruiser 70 / 80 Series - Prado 90 / 120 Series
AUD $190.91AUD $381.82 (ex. tax)× -
Diff Overhaul Kit - LandCruiser 71, 76, 78, 79, 100, 105, 200 Series - Factory Diff Lock & Spacer (Rear)
AUD $463.64AUD $927.27 (ex. tax)× -
Fan Shroud and Electric Fan Kit - Toyota Hilux LS2 / LS3 V8 (2005-2015) KUN26R
AUD $1,695.45AUD $1,695.45 (ex. tax)× -
Mitsubishi Gen 3 - Low Range Gears 66% (3.15:1) Reduction (Auto)
AUD $2,177.27AUD $2,177.27 (ex. tax)× -
Bell Housing Adaptor Kit - Chev V8 Diesel (6.2L, 6.5L) to LandCruiser 60, 70 Series 10/1984 on (Manual)
AUD $3,818.18AUD $3,818.18 (ex. tax)× -
Engine Chassis Brackets - Chev V8 to Landcruiser 80 / 105 Series
AUD $631.82AUD $631.82 (ex. tax)× -
Bell Housing Adaptor Kit - Chev V8 Petrol (early) - 168 Tooth Flywheel to LandCruiser pre 10/1984 (Manual)
AUD $4,000.00AUD $4,000.00 (ex. tax)× -
Swivel Housing Overhaul Kit - LandCruiser VDJ76, 78, 79 (Non-ABS) & HZJ70 Series
AUD $313.64AUD $313.64 (ex. tax)× -
Navara D40 Ø 320mm - Delios Slotted Front Brake Rotors (1 x Pair)
AUD $290.91AUD $290.91 (ex. tax)× -
Chev V8 to LandCruiser 55 / 75 series - Engine Mount Kit (Heavy Duty)
AUD $568.18AUD $568.18 (ex. tax)× -
Brake Master Cylinder - LandCruiser FZJ70, 75, 80 / HZJ70, 73, 75 Series
AUD $188.38AUD $188.38 (ex. tax)× -
Gear Select Module - Black Anodized Push Button Shifter Remote
AUD $2,150.00AUD $4,300.00 (ex. tax)× -
Catch Can & Diesel Fuel Water Separator kit by Ryco - Nissan Navara
AUD $760.00AUD $760.00 (ex. tax)× -
Transfer Case Rebuild Kit - LandCruiser 70 / 80 Series (Part Time 4WD)
AUD $636.36AUD $636.36 (ex. tax)× -
Navara D40 Ø 295mm - Delios Slotted Front Brake Rotors (1 x Pair)
AUD $268.18AUD $268.18 (ex. tax)× -
Viscous Fan Assembly (Long Version) - LS Series V8 Engines (LandCruiser / Patrol)
AUD $813.64AUD $813.64 (ex. tax)× -
Transfer Case Adaptor - 4L60E to LandCruiser 80, 100 Series 5-Speed (HF2A Case)
AUD $1,986.36AUD $1,986.36 (ex. tax)× -
LS Series V8 to LandCruiser 70 Series 1VD 4.5L V8 (5-speed manual)
AUD $3,954.55AUD $3,954.55 (ex. tax)× -
Clutch Kit (Organic Plate) - Chev V8 Petrol 12" - 10 Tooth Spline
AUD $972.00AUD $972.00 (ex. tax)× -
Accessory Mount Kit - Alternator (RHS) High Mount & A/C Compressor (LHS) Low Mount - LS V8 6.0L, 6.2L (VE-VF)
AUD $540.91AUD $540.91 (ex. tax)× -
5th Gear Overdrive Ratio Change - LandCruiser HZJ, Hilux Series (from 0.838 to 0.711)
AUD $572.73AUD $572.73 (ex. tax)×
Mitsubishi Gen 2 – Low Range Gears – 66% (3.15:1) Reduction – Auto
AUD $2,395.00 (Excl. Tax AUD $2,177.27)
Mitsubishi low range gears – ratio 3.15:1 – automatic transmission
To Suit
Generation 2 transfer case – 23 tooth (spline) input gear
- Montero
- Pajero
- Shogun
- Triton
Mitsubishi Gen 2 – Low Range Gears – 66% (3.15:1) Reduction
Marks 4WD Adaptors manufacture low range reduction gears to suit many models of Mitsubishi Pajero, Montero, Shogun and Triton. These gears are manufactured in house at our facility in Melbourne, Australia. We manufacture two reduction ratios for the Generation 2 transfer cases to suit different vehicle applications and requirements.
The 66% reduction gears give you the biggest reduction we offer and suit vehicles fitted with a automatic transmission. These are mainly suited to rock crawling vehicles or vehicles that are prone to run away down hill (fitted with an automatic transmission). As an example this reduction gives a manual vehicle about one and a half gears below where the factory gearing sat. High range is not altered when fitting our low range gears.
To calculate your vehicle’s ratio, click here.
Will these gears fit my vehicle?
You will need to remove and open the transfer case and check the idler gear has external shoulders for the roller bearings and the face width of the gear must be approximately 30mm and 28mm respectively. Please see image below for reference;
Mitsubishi Pajero Gen 2 Low Range Gear Measurements
Features
- 100% Australian Made
- Designed & Manufactured in-house at Marks4wd
Kit Includes
- Input gear
- Idler gear
- Output gear
- Roller bearing
- Seals
To Suit – Mitsubishi
Generation 2 transfer case – 23 tooth (spline) input gear
- Montero
- Pajero
- Shogun
- Triton
Notes
- A Mitsubishi workshop manual is required for fitment
- The input gear spline is 23T – 31.3mm in diameter
Customers reviews
Only logged in customers who have purchased this product may leave a review.
There are no reviews yet.