-
Clutch Kit (Organic Plate) - Chev V8 Petrol 12" - 10 Tooth Spline
AUD $972.00AUD $2,916.00 (ex. tax)× -
Nissan Patrol GQ / GU - Low Range Gear Set - 24% (2.484:1) Reduction
AUD $1,813.64AUD $1,813.64 (ex. tax)× -
Navara D40 Ø 295mm - Delios Slotted Front Brake Rotors (1 x Pair)
AUD $268.18AUD $268.18 (ex. tax)× -
Diff Overhaul Kit - LandCruiser 71, 76, 78, 79, 200 Series (5/15 -) (Rear)
AUD $431.82AUD $431.82 (ex. tax)× -
Bell Housing Adaptor Kit - Chev V8 Petrol (early) 168 Tooth Flywheel to LandCruiser 4.5L Gearbox (5-speed manual)
AUD $3,445.45AUD $3,445.45 (ex. tax)× -
Fan Shroud & Hose Kit - LS Series V8 to Patrol GU (RD28 / ZD30)
AUD $1,059.09AUD $1,059.09 (ex. tax)× -
Mitsubishi Gen 3 - Low Range Gears 66% (3.15:1) Reduction (Manual)
AUD $2,177.27AUD $2,177.27 (ex. tax)× -
Bell Housing Adaptor Kit - Chev V8 Petrol to Land Rover / Range Rover (4 / 5-speed manual)
AUD $1,500.00AUD $1,500.00 (ex. tax)× -
Engine Chassis Brackets - Chev V8 to Toyota Landcruiser 55 / 75 Series
AUD $190.91AUD $190.91 (ex. tax)× -
Bell Housing Adaptor Kit - Chev V8 Petrol (early) - 168 Tooth Flywheel to LandCruiser 60, 70 Series (Manual)
AUD $3,818.18AUD $3,818.18 (ex. tax)× -
Radiator & Heater Hose Kit - LS Series V8 to LandCruiser 80 Series
AUD $113.64AUD $113.64 (ex. tax)× -
Catch Can & Diesel Fuel Water Separator kit by Ryco - Mitsubishi Pajero Sport & Triton
AUD $760.00AUD $760.00 (ex. tax)× -
Ultra Vision Nitro Maxx 24" 205W LED Light Bar (4500K) Hi/Lo Beam
AUD $899.09AUD $899.09 (ex. tax)× -
Diff Overhaul Kit - LandCruiser 71, 76, 78, 79, 100, 105, 200 Series - Factory Diff Lock & Spacer (Rear)
AUD $463.64AUD $463.64 (ex. tax)× -
Diff Overhaul Kit - LandCruiser 71, 76, 78, 79, 100, 105, 200 Series LandCruiser - Solid Spacer Diff (Rear)
AUD $346.36AUD $346.36 (ex. tax)× -
Bendix Ultimate 4WD Brake Pads - Toyota Hilux 2.8D (GUN126) (Front Pads)
AUD $268.18AUD $268.18 (ex. tax)× -
LED Light Stand - FLi PRO Telescoping 2.5 Metres (8ft) Removeable Flashlight, Wireless Remote & USB Chargeable
AUD $236.36AUD $236.36 (ex. tax)× -
Accessory Mount Kit - Alternator (LHS) High Mount & A/C Compressor (LHS) Low Mount- LS V8 6.0L, 6.2L (VE-VF)
AUD $1,031.82AUD $1,031.82 (ex. tax)× -
Mitsubishi Gen 3 - Low Range Gears 66% (3.15:1) Reduction (Auto)
AUD $2,177.27AUD $2,177.27 (ex. tax)× -
5th Gear Overdrive Ratio Change - LandCruiser HZJ, Hilux Series (from 0.838 to 0.711)
AUD $572.73AUD $572.73 (ex. tax)×
Mitsubishi Gen 3 – Low Range Gears 66% (3.15:1) Reduction (Manual)
AUD $2,395.00 (Excl. Tax AUD $2,177.27)
To Suit – Mitsubishi
- Generation 3 transfer case – 24 tooth (spline) input gear
- Montero
- Pajero
- Shogun
Low Range Gears 66% (3.15:1) Reduction (Manual) to suit Mitsubishi Gen 3
Marks 4WD Adaptors manufacture low range reduction gears to suit many models of Mitsubishi Pajero, Montero and Shogun. These gears are manufactured in-house at our facility in Melbourne, Australia. We manufacture two reduction ratios for the Generation 3 transfer cases to suit different vehicle applications and requirements.
The 66% reduction gears give you a great overall reduction and suit vehicles fitted with a manual transmission. These are mainly suited vehicles used for rock crawling, sand, desert or vehicles that are prone to run away downhill. For example, this reduction gives a manual vehicle about one and a half gears below where the factory gearing sat. High range is not altered when fitting our low-range gears.
To calculate your Vehicle’s ratio, click here.
Will these Gears fit my Vehicle?
You will need to remove and open the transfer case and check the idler gear has external shoulders for the roller bearings and that the face width of the gear must be approximately 25mm and 20mm, respectively. Please see the image below for reference;
Mitsubishi Pajero Gen 3 Low Range Gear Measurements
Features
- 100% Australian Made
- Designed & Manufactured in-house at Marks4wd
Kit Includes
- Input gear
- Idler gear
- Output gear
- Backlash eliminator
- Downloadable Instructions (requires login)
To Suit – Mitsubishi
- Generation 3 transfer case – 24 tooth (spline) input gear
- Montero
- Pajero
- Shogun
Notes
- A Mitsubishi workshop manual is required for fitment
- The input gear spline is 24T
Customers reviews
Only logged in customers who have purchased this product may leave a review.
There are no reviews yet.