-
Mitsubishi Gen 3 - Low Range Gears 66% (3.15:1) Reduction (Auto)
AUD $2,177.27AUD $2,177.27 (ex. tax)× -
Bell Housing Adaptor Kit - Holden V8 (Turbo Pattern) to LandCruiser 4.2L 1HZ (5-speed)
AUD $4,059.09AUD $4,059.09 (ex. tax)× -
Viscous Fan Assembly (Long Version) - LS Series V8 Engines (LandCruiser / Patrol)
AUD $813.64AUD $813.64 (ex. tax)× -
Diff Overhaul Kit - LandCruiser 76, 78, 79, 100, 105, 200 Series (Rear)
AUD $404.55AUD $809.09 (ex. tax)× -
Nissan Patrol GQ / GU - Low Range Gear Set - 43% (2.86:1) Reduction
AUD $1,813.64AUD $1,813.64 (ex. tax)× -
Bell Housing Adaptor Kit - LS Series V8 to LandCruiser 80, 105 Series 4.5L (5-speed manual)
AUD $3,390.91AUD $3,390.91 (ex. tax)× -
Holden V8 to LandCruiser 55 / 75 Series - Engine Chassis Brackets
AUD $450.00AUD $450.00 (ex. tax)× -
Mitsubishi Gen 2 - Low Range Gears - 40% (2.7:1) Reduction (Manual)
AUD $2,177.27AUD $2,177.27 (ex. tax)× -
Diff Overhaul Kit - LandCruiser VDJ70 series (Front) - Prado / Hilux Rear (Factory Diff Lock)
AUD $450.00AUD $450.00 (ex. tax)× -
Penrite Pro Gear 80W-140 API GL-5 Full Synthetic Gear Oil - 1 Litre
AUD $17.27AUD $17.27 (ex. tax)× -
Bendix 4WD ULT Brake Rotors - Ford Ranger PX / Mazda BT50 (Front Rotors)
AUD $368.18AUD $368.18 (ex. tax)× -
Bell Housing Adaptor Kit - LS Series V8 to Patrol GU (ZD30 - Auto)
AUD $1,813.64AUD $1,813.64 (ex. tax)× -
Bendix 4WD Brake Rotors - Toyota LandCruiser 200 Series (VX / Sahara) (Front Rotors)
AUD $450.00AUD $450.00 (ex. tax)× -
Clutch Kit - Holden VR Series 2 VS / VT (T5 manual) 10.5" - 10T Spline
AUD $404.55AUD $404.55 (ex. tax)× -
Gear Select Module Install Kit - to suit GM without PRNDL and 6L80
AUD $86.36AUD $86.36 (ex. tax)× -
Alternator Relocation Kit (LHS) High Mount & Engine Driven Fan Kit - LSA Series V8
AUD $2,659.09AUD $5,318.18 (ex. tax)× -
Accessory Mount Kit - Alternator (RHS) High Mount & A/C Compressor (LHS) Low Mount - LS V8 6.0L, 6.2L (VE-VF)
AUD $540.91AUD $540.91 (ex. tax)×
Bell Housing Adaptor Kit – LS Series V8 to LandCruiser 4.2L (5-speed manual)
AUD $3,870.00 (Excl. Tax AUD $3,518.18)
Bell Housing Adaptor Kit to suit LS Series V8 to Toyota LandCruiser (4.2L vehicles) engine conversion fitted with a factory 5-speed manual gearbox.
To Suit
- Toyota LandCruiser – 4.2L 1HDT (factory 5-speed manual)
- LS1, LS2, LS3 Series V8’s
Bell Housing Adaptor Kit to suit LS Series V8 to Toyota LandCruiser 4.2L (5-speed manual)
This kit comprises of a flywheel housing running a 3 piece steel flywheel.
The flywheel housing is supplied which measures 61 mm/2.4″ long. This housing has the GM bolt pattern on the front and the Toyota 1HDT, bolt pattern on the rear.
The kit is supplied with a flex plate stiffener which bolts up to the original GM flex plate, the stiffener is basically a very thin flywheel. A crankshaft adaptor/spacer is bolted to the crankshaft which also secures the flex plate/ring gear and flex plate stiffener to the crankshaft. The original GM flex plate with the 168-tooth ring gear is used. The new steel flywheel is drilled and doweled to accept the standard LandCruiser 4.2L 12″ 14T clutch as fitted to HDT## series engines.
The flywheel assembly is offset to the rear to place the clutch in its original position.
The flywheel assembly is heavier than a standard flywheel, giving greater inertia allowing the engine to idle smoother. The extra weight also helps to give less chance of stalling the engine when off road, climbing over rocks, and taking off on steep inclines. The extra weight of the flywheel has no adverse effect on the engine.
The kit is also supplied with an oil pressure sensor adaptor, the adaptor is fitted in place of the of the GM sender located behind the intake manifold at the back of the engine block.
A water temperature adaptor is also supplied, the adaptor is fitted in the right-hand cylinder head behind the exhaust manifold, it accepts the original Toyota sender.
Clutch Kits
Kit Contains
- Adaptor flywheel housing
- Flexplate stiffener
- Crankshaft adaptor
- Flywheel
- Dowels
- Flywheel cover plate
- Spigot bearing
- Oil pressure sender adaptor
- Water temperature sender adaptor
- Spacers, Bolts, Washers
- Downloadable Instructions (requires login)
To Suit
- Toyota LandCruiser 4.2L 1HDT (factory 5-speed manual)
- LS1, LS2, LS3 Series V8’s
Notes
- The original GM 168 tooth auto flex plate is reused for this conversion
Customers reviews
Only logged in customers who have purchased this product may leave a review.
There are no reviews yet.