-
Mitsubishi Gen 3 - Low Range Gears 66% (3.15:1) Reduction (Auto)
AUD $2,177.27AUD $2,177.27 (ex. tax)× -
Brake Master Cylinder - LandCruiser FZJ70, 75, 80 / HZJ70, 73, 75 Series
AUD $188.38AUD $188.38 (ex. tax)× -
LandCruiser 100 Series - Delios Slotted Rear Disc Rotors Pair - DLS789
AUD $300.00AUD $300.00 (ex. tax)× -
Bell Housing Adaptor Kit - Holden V8 (Turbo Pattern) to LandCruiser FJ Petrol (auto)
AUD $2,495.45AUD $2,495.45 (ex. tax)× -
Fan Shroud and Electric Fan Kit - Toyota Hilux LS2 / LS3 V8 (2005-2015) KUN26R
AUD $1,695.45AUD $1,695.45 (ex. tax)× -
Clutch Kit - Holden VR Series 2 VS / VT (T5 manual) 10.5" - 10T Spline
AUD $404.55AUD $809.09 (ex. tax)× -
Nissan Patrol GU - LS Series V8 Manual - Stainless Steel Exhaust Headers
AUD $1,318.18AUD $1,318.18 (ex. tax)× -
Mitsubishi Gen 2 - Low Range Gears - 40% (2.7:1) Reduction (Manual)
AUD $2,177.27AUD $2,177.27 (ex. tax)× -
LandCruiser 70, 105 Series - Delios Slotted Front Brake Rotors (1 x Pair)
AUD $281.82AUD $281.82 (ex. tax)× -
Catch Can / Oil Separator Kit (Ryco Filter) - LandCruiser VDJ70 Series
AUD $418.18AUD $418.18 (ex. tax)× -
LandCruiser 105 Series - Delios Slotted Rear Brake Rotors (1 x Pair)
AUD $281.82AUD $281.82 (ex. tax)× -
Handbrake Shoe Kit - LandCruiser 70 / 80 Series - Prado 90 / 120 Series
AUD $190.91AUD $190.91 (ex. tax)× -
Gear Indicator - 6 Speed Gearboxs - 6L50, 6L80, 6L90 / VE, VF Commodore / Colorado
AUD $222.73AUD $222.73 (ex. tax)× -
Ryco Cabin Air Filter - LandCruiser VDJ70 Series (N99 MicroShield)
AUD $28.81AUD $28.81 (ex. tax)× -
Diff Overhaul Kit - Nissan Navara D40, D23 NP300 & Pathfinder R51 (Front)
AUD $695.45AUD $695.45 (ex. tax)× -
LandCruiser 200 Series - Delios Slotted Front Brake Rotors (1 x Pair)
AUD $340.91AUD $340.91 (ex. tax)× -
Bell Housing Adaptor Kit - Holden V8 (Turbo Pattern) to LandCruiser 4.5L (5-speed manual)
AUD $3,931.82AUD $7,863.64 (ex. tax)× -
Wheel Bearing Kit - LandCruiser (1975-2012) & Hilux (Up to '97) Drum Brakes
AUD $63.64AUD $63.64 (ex. tax)× -
Bendix Ultimate 4WD Brake Pads - Toyota LandCruiser 70, 100 Series (Front Pads)
AUD $213.64AUD $213.64 (ex. tax)× -
Viscous Fan Assembly (Long Version) - LS Series V8 Engines (LandCruiser / Patrol)
AUD $813.64AUD $813.64 (ex. tax)× -
Bell Housing Adaptor Kit - LS Series V8 to Patrol GU ZD30 (5-speed manual)
AUD $3,540.91AUD $3,540.91 (ex. tax)×
Mitsubishi Gen 3 – Low Range Gears 66% (3.15:1) Reduction (Manual)
AUD $2,395.00 (Excl. Tax AUD $2,177.27)
To Suit – Mitsubishi
- Generation 3 transfer case – 24 tooth (spline) input gear
- Montero
- Pajero
- Shogun
Low Range Gears 66% (3.15:1) Reduction (Manual) to suit Mitsubishi Gen 3
Marks 4WD Adaptors manufacture low range reduction gears to suit many models of Mitsubishi Pajero, Montero and Shogun. These gears are manufactured in-house at our facility in Melbourne, Australia. We manufacture two reduction ratios for the Generation 3 transfer cases to suit different vehicle applications and requirements.
The 66% reduction gears give you a great overall reduction and suit vehicles fitted with a manual transmission. These are mainly suited vehicles used for rock crawling, sand, desert or vehicles that are prone to run away downhill. For example, this reduction gives a manual vehicle about one and a half gears below where the factory gearing sat. High range is not altered when fitting our low-range gears.
To calculate your Vehicle’s ratio, click here.
Will these Gears fit my Vehicle?
You will need to remove and open the transfer case and check the idler gear has external shoulders for the roller bearings and that the face width of the gear must be approximately 25mm and 20mm, respectively. Please see the image below for reference;
Mitsubishi Pajero Gen 3 Low Range Gear Measurements
Features
- 100% Australian Made
- Designed & Manufactured in-house at Marks4wd
Kit Includes
- Input gear
- Idler gear
- Output gear
- Backlash eliminator
- Downloadable Instructions (requires login)
To Suit – Mitsubishi
- Generation 3 transfer case – 24 tooth (spline) input gear
- Montero
- Pajero
- Shogun
Notes
- A Mitsubishi workshop manual is required for fitment
- The input gear spline is 24T
Customers reviews
Only logged in customers who have purchased this product may leave a review.
There are no reviews yet.