-
Clutch Kit (Organic Plate) - Chev V8 Petrol 12" - 10 Tooth Spline
AUD $972.00AUD $972.00 (ex. tax)× -
Wheel Bearing Kit - LandCruiser (1975-2012) & Hilux (Up to '97) Drum Brakes
AUD $63.64AUD $63.64 (ex. tax)× -
Catch Can & Diesel Fuel Water Separator kit by Ryco - Mitsubishi Triton / Challenger
AUD $760.00AUD $760.00 (ex. tax)× -
Bell Housing Adaptor Kit - Chev V8 Petrol (late) to LandCruiser FJ (Auto)
AUD $2,995.45AUD $2,995.45 (ex. tax)× -
Navara D40 Ø 295mm - Delios Slotted Front Brake Rotors (1 x Pair)
AUD $268.18AUD $268.18 (ex. tax)× -
Gear Select Module Install Kit - GM 4L60, 65, 70, 80, 85 with PRNDL
AUD $86.36AUD $86.36 (ex. tax)× -
Bell Housing Adaptor Kit - Chev V8 Petrol (late) 168 Tooth Flywheel to LandCruiser 4.2L (5-speed manual)
AUD $3,713.64AUD $3,713.64 (ex. tax)× -
Bell Housing Adaptor Kit - Chev V8 Diesel to LandCruiser FZ80, FZ105 4.5L (5-speed manual)
AUD $3,904.55AUD $3,904.55 (ex. tax)× -
Chassis Mount Bracket (Heavy Duty) - Hilux LN / RN (LFS) Single bracket
AUD $200.00AUD $200.00 (ex. tax)× -
Bell Housing Adaptor Kit - Chev V8 Petrol (late) 168 Tooth Flywheel to LandCruiser 4.2L (5-speed manual)
AUD $4,454.55AUD $4,454.55 (ex. tax)× -
Toyota LandCruiser 80, 105 Series - LS V8 (4L60E / 6L80E) - Stainless Steel Exhaust Headers
AUD $1,222.73AUD $1,222.73 (ex. tax)× -
Water Temperature Sensor Adaptor - Chev & Holden V8 to Toyota (non EFI)
AUD $40.91AUD $40.91 (ex. tax)× -
Ultra Vision - Single Pole (On/Off) Switch- LandCruiser 70, 100, 105 series, Hilux, Prado 120
AUD $29.09AUD $29.09 (ex. tax)× -
Ultra Vision - Behind Grille LED Light Bar - Next-Gen Ford Ranger Raptor & Wildtrack
AUD $1,136.36AUD $1,136.36 (ex. tax)× -
Gear Indicator - 6 Speed Gearboxs - 6L50, 6L80, 6L90 / VE, VF Commodore / Colorado
AUD $222.73AUD $222.73 (ex. tax)× -
Bell Housing Adaptor Kit - Chev V8 Petrol (late) - 168 Tooth Flywheel to LandCruiser 10/1984 on (Manual)
AUD $3,818.18AUD $3,818.18 (ex. tax)× -
Transfer Case Adaptor - 4L60E 6-bolt to Hilux V6 5-Speed, 26T Input Spline (Chain Driven Case)
AUD $2,931.82AUD $2,931.82 (ex. tax)× -
Bell Housing Adaptor Kit - Chev V8 Petrol (late) to Rover (ZF 4-speed auto)
AUD $1,813.64AUD $1,813.64 (ex. tax)×
- You cannot add "Mitsubishi Gen 1 - Low Range Gears 48% (2.85:1) Reduction (Manual)" to the cart because the product is out of stock.
Mitsubishi Gen 3 – Low Range Gears 66% (3.15:1) Reduction (Manual)
AUD $2,395.00 (Excl. Tax AUD $2,177.27)
To Suit – Mitsubishi
- Generation 3 transfer case – 24 tooth (spline) input gear
- Montero
- Pajero
- Shogun
Low Range Gears 66% (3.15:1) Reduction (Manual) to suit Mitsubishi Gen 3
Marks 4WD Adaptors manufacture low range reduction gears to suit many models of Mitsubishi Pajero, Montero and Shogun. These gears are manufactured in-house at our facility in Melbourne, Australia. We manufacture two reduction ratios for the Generation 3 transfer cases to suit different vehicle applications and requirements.
The 66% reduction gears give you a great overall reduction and suit vehicles fitted with a manual transmission. These are mainly suited vehicles used for rock crawling, sand, desert or vehicles that are prone to run away downhill. For example, this reduction gives a manual vehicle about one and a half gears below where the factory gearing sat. High range is not altered when fitting our low-range gears.
To calculate your Vehicle’s ratio, click here.
Will these Gears fit my Vehicle?
You will need to remove and open the transfer case and check the idler gear has external shoulders for the roller bearings and that the face width of the gear must be approximately 25mm and 20mm, respectively. Please see the image below for reference;
Mitsubishi Pajero Gen 3 Low Range Gear Measurements
Features
- 100% Australian Made
- Designed & Manufactured in-house at Marks4wd
Kit Includes
- Input gear
- Idler gear
- Output gear
- Backlash eliminator
- Downloadable Instructions (requires login)
To Suit – Mitsubishi
- Generation 3 transfer case – 24 tooth (spline) input gear
- Montero
- Pajero
- Shogun
Notes
- A Mitsubishi workshop manual is required for fitment
- The input gear spline is 24T
Customers reviews
Only logged in customers who have purchased this product may leave a review.
There are no reviews yet.